Lista:
(IC1) >>>> 1 x Pic 18f2550 (suerte en tu busqueda)
.>>>>>>>> 1 x zocalo de 28 patillas (obligatorio)
(LED) >>>> 1 x led (color que quieras)
(R1) >>>>> 1 x resistencia de 330 ohmios (en el esquema es de 1K, pon la que quieras, da lo mismo)
(R2 y R3) > 2x resistencia de 10K (estas son solo si quieres la version bootloader)
(JP1) >>>> 1x jumper de 2 pines con caperuza (esto es solo si quieres la version bootloader)
(C1 y C2) > 2 x condesadores de 22pf (tienen que entrar debajo del chip, OJO al tamaño del condensador)
(C3) >>>>> 1 x condensador de 470nf (en el esquema es de 220nF, pon el que quieras, seguramente funcione igual)
(C4) >>>>> 1 x condensador de 100nf (este no esta en el esquema original, le he añadido yo)
(Q1) >>>>> 1 x cristal de cuarzo de 8Mhz (el del esquema es de 20Mhz, tu mismo xD)
..>>>>>>>> 1 x conector USB tipoB hembra (si no es este, no te valdra la placa mia) (esta hecho con este conector porque el macho Tipo A es muy dificil de encontrar)
Hex:
Se GRABA con un programador (TE-20 por ejemplo), no lleva bootloader
How to JailBreak PS3 with Blackcat USB
Requirements:
PS3 (on fw 3.41)
Blackcat USB
Flip Software (i used 3.3.1)
Psgroove Teensy 1.0 Hex file w/ Manager.pkg
Manager.pkg file
External USB Drive
Original PS3 Game Disc
1) Put the Blackcat USB in DFU mode by flipping both switches to the 1 an 2 positions.
2) Push the button on the board and look at Device Manager, if it shows up as AT90USB162 you're in DFU mode.
3) Open Flip and select target device AT90USB162.
4) Now go into Settings and select a communication medium, choose USB. Your Blackcat's info should show up.
5) Go to File, hit Load Hex File, and choose the Teensy 1.0 hex file.
6) Erase, Blank Check it, and write the Hex file onto the chip.
7) Hit the verify button to make sure it went through ok, if so just hit the "Start Application" button.
8) Load the Manager.pkg onto the external drive. (Formatted FAT32)
9) Go to your PS3 and do a complete power cycle. (Turn off completely with switch on back.)
10) Plug in your Blackcat USB, turn on the switch in back.
11) Power on your PS3 and hit the eject button immediately. (This is the part most people mess up.)
12) If you did it right, you will have two folders on your XMB. One that says "Install Package Files" and another "/app_home/PS3_GAME/".
13) Plug in your USB drive with the Manager.pkg file. You should now see it in the "Install Package Files" folder. Run it. You should now have Package Manager installed.
14) Install your original PS3 game and run Package Manager. It will ask you whether you want to load it or back it up. Back it up!
15) After a few minutes you'll have a copy of the game showing up. Select it and it will load it to the XMB menu.
16) Hit the game icon and Play!!! ENJOY!!!
http://rapidshare.com/files/420262710/PSGrooPICV1.4_HEX_CCS.hex
http://rapidshare.com/files/420262730/PSGrooveBlackcatUSB.rar
(IC1) >>>> 1 x Pic 18f2550 (suerte en tu busqueda)
.>>>>>>>> 1 x zocalo de 28 patillas (obligatorio)
(LED) >>>> 1 x led (color que quieras)
(R1) >>>>> 1 x resistencia de 330 ohmios (en el esquema es de 1K, pon la que quieras, da lo mismo)
(R2 y R3) > 2x resistencia de 10K (estas son solo si quieres la version bootloader)
(JP1) >>>> 1x jumper de 2 pines con caperuza (esto es solo si quieres la version bootloader)
(C1 y C2) > 2 x condesadores de 22pf (tienen que entrar debajo del chip, OJO al tamaño del condensador)
(C3) >>>>> 1 x condensador de 470nf (en el esquema es de 220nF, pon el que quieras, seguramente funcione igual)
(C4) >>>>> 1 x condensador de 100nf (este no esta en el esquema original, le he añadido yo)
(Q1) >>>>> 1 x cristal de cuarzo de 8Mhz (el del esquema es de 20Mhz, tu mismo xD)
..>>>>>>>> 1 x conector USB tipoB hembra (si no es este, no te valdra la placa mia) (esta hecho con este conector porque el macho Tipo A es muy dificil de encontrar)
Hex:
Se GRABA con un programador (TE-20 por ejemplo), no lleva bootloader
How to JailBreak PS3 with Blackcat USB
Requirements:
PS3 (on fw 3.41)
Blackcat USB
Flip Software (i used 3.3.1)
Psgroove Teensy 1.0 Hex file w/ Manager.pkg
Manager.pkg file
External USB Drive
Original PS3 Game Disc
1) Put the Blackcat USB in DFU mode by flipping both switches to the 1 an 2 positions.
2) Push the button on the board and look at Device Manager, if it shows up as AT90USB162 you're in DFU mode.
3) Open Flip and select target device AT90USB162.
4) Now go into Settings and select a communication medium, choose USB. Your Blackcat's info should show up.
5) Go to File, hit Load Hex File, and choose the Teensy 1.0 hex file.
6) Erase, Blank Check it, and write the Hex file onto the chip.
7) Hit the verify button to make sure it went through ok, if so just hit the "Start Application" button.
8) Load the Manager.pkg onto the external drive. (Formatted FAT32)
9) Go to your PS3 and do a complete power cycle. (Turn off completely with switch on back.)
10) Plug in your Blackcat USB, turn on the switch in back.
11) Power on your PS3 and hit the eject button immediately. (This is the part most people mess up.)
12) If you did it right, you will have two folders on your XMB. One that says "Install Package Files" and another "/app_home/PS3_GAME/".
13) Plug in your USB drive with the Manager.pkg file. You should now see it in the "Install Package Files" folder. Run it. You should now have Package Manager installed.
14) Install your original PS3 game and run Package Manager. It will ask you whether you want to load it or back it up. Back it up!
15) After a few minutes you'll have a copy of the game showing up. Select it and it will load it to the XMB menu.
16) Hit the game icon and Play!!! ENJOY!!!
http://rapidshare.com/files/420262710/PSGrooPICV1.4_HEX_CCS.hex
http://rapidshare.com/files/420262730/PSGrooveBlackcatUSB.rar